Ford’s auto transmission

The era between 1964 and the 1980s was remarkable in the automobile industry. During this period, millions of Ford vehicles – i.e., cars and trucks – were equipped with C4 and C5 automatic transmissions. These were purely ford automatic transmissions – i.e., zero electronic controls – that were very popular with hot rodders, racers, as well as restorers due to their low cost and simplicity.

However, despite the possibility of purchasing cores and rebuilding in order to suit the requirements of a particular vehicle for a far less rebuilt modern overdrive automatic transmission with electronic controls, they lacked the lockup torque converters and overdriven gears newer transmissions rely heavily upon in order to boost fuel economy. Ford faced a seemingly insurmountable challenge in the late 1950s: shedding the old-fashioned technology and dated image. However, the carmaker faced the challenge head-on, beginning in 1958 with the new generation of the FE-series V-8 engines. 

Before 1960, Ford vehicles were burdened with heavily obsolete BorgWarner-designed cast-iron FX and MX automatic transmissions famously called Ford-O-Matics, Cruise-O-Matics, and Merc-O-Matics. The FX was small, while the MX was a popular large-case automatic. These were rugged, dependable, and heavy transmissions, so complex that adapting them to performance applications was next to impossible.

Falcon and Comet

Ford introduced its Falcon and Comet sixes in 1960. Just before then, Ford engineers had painstakingly developed lightweight aluminum-case automatic transmissions for the exciting lineup of vehicles that arrived in the ’60s. Soon enough, the 90-degree Fairlane small-block V8s followed the lightweight-iron Falcon and Comet sixes in 1962. The Mercury Comet and Ford Falcon, introduced in the ’60s, came with the new lightweight Ford-O-Matic two-speed transmission. BorgWarner manufactured this 2-speed transmission for new-generation small V-8s and straight-6.

The hard steel parts inside and out and its aluminum case made the Ford-O-Matic different from its predecessor. In its early application, the Ford-O-Matic transferred heat to the atmosphere through the cooling vents in the bell housing and torque converter. There was no transmission cooler in the radiator, and no fluid was used as a coolant. However, later versions of this Ford transmission came with a transmission fluid cooler in the radiator. In addition, the Merc-O-Matic/Ford-O-Matic came with a case-fill dipstick tube, with the main case and bell housing cast as one, in order to reduce the likelihood of leakage and excess weight.

The Ford C4 Transmission

After learning a lot from the BorgWarner 2-speed automatic transmission, Ford took its knowledge and used it to build the C4 3-speed automatic transmission known as the Cruise-O-Matic for the 1964 model year.

• The C4 automatic transmission was manufactured at Ford’s transmission plant in Sharonville, Ohio, from 1964 to 1981. It was the first automatic transmission Ford solely designed and constructed. It utilized a new, cutting-edge Simpson compound planetary gear set that became the industry standard for decades.
• The C4 automatic transmission earned its name from the model year it was manufactured, i.e., ‘C’ denotes the ’60s decade while ‘4’ was for the year 1964. However, this naming practice lasted less time than expected, as the transmissions that followed were C3 in the ’70s and C5 in the ’80s.
• The C4 was known as the ‘Dual-Range Cruise-O-Matic’ from ’64 to ’66, otherwise known as the Green Dot transmission. This transmission was equipped with a unique valve body that enables you to start driving in second gear on snow and ice with a 2-3 upshift. This is the small dot on the indicator.

The larger green dot near ‘L’ at the detent allows a driver to start in first gear and go through the typical 1-2-3 upshift program.

Cruise-O-Matic

Ford called its new automatic transmission the Cruise-O-Matic, but Mercury called its own the Merc-O-Matic. Bear in mind that ‘Cruise-O-Matic’ was the broad marketing name for the Ford automatic transmissions created in the mid-’60s era. But by 1967, the name ‘Cruise-O-Matic’ was dropped in favor of the name ‘Select-Shift’ and was picked up and used for all automatic transmissions from Ford. The C4 automatic transmission only had the 5-bolt bell housing for V-8s for only the 1964 model year. However, by August 1964, the V-8s and C4 it was mated to were ingeniously fitted into the larger 6-bolt bell housing in order to reduce vibration, noise, and harshness.

The following are the C4 gear ratios:

• First gear – 2.46:1
• Second gear – 1.46:1
• Third gear – 1.00:1
• Reverse gear – 2.20:1

The C4 transmission evolved, resulting in the introduction of other design changes. The most notable was the ’67 and ’69 valve body that offers a traditional P-R-N-D-2-1 shift pattern.

The Ford C5 Transmission

Ford introduced the popular C5 Select-Shift transmission in 1982. Its only difference from its predecessor was that it came with a locking torque converter in order to boost fuel economy significantly. The C5 automatic transmission remained in production from 1982 to 1986 at Ford’s transmission and axle plant in Livonia, Michigan. But it wasn’t recommended as one of the high-performance transmissions. Nevertheless, the C5 transmission shares most of its internal components with its predecessor, including the cases. The C5 transmission was manufactured as pan-fill and case-fill with 157- or 167-tooth flexplates.

The Ford C6 Transmission 

Ford introduced its heavy-duty C6 –speed transmission for high-torque applications. This automatic transmission was behind the large-displacement big-block V-8s. Its internal components and case were entirely different from the C4 transmission, but internally, they were the same, though scaled largely for heavy-duty use.

The rugged C6 transmission had four basic bell housing bolt patterns throughout its long production life as it was designed solely for high-power applications. There’s also the small-block C6 automatic transmission intended only for 351W as well as 351C engines and fits any 6-bolt 289/302/351W/51C small-block bell housing bolt pattern.

The C6 transmission for diesel engines was produced in the ’80s before the introduction of the 4R100 (E4OD) in 1989. Despite the arrival of the 4R100, Ford continued producing the C6 automatic transmission for industrial applications until 1996.

The arrival of the ’70s met Ford with a respectable lineup of great and modern lightweight automatic transmissions. Here are the C6 gear ratios:

• First Gear – 2.46:1
• Second Gear – 1.46:1
• Third Gear – 1.00:1
• Reverse – 2.00:1

Conclusion

Ford has undergone decades of performance evolution from it’s first automatic transmission to the current one in the market. The current transmission may not be perfect in every sense. But it is sure the car maker will improve its transmissions to deliver worthy experiences for their esteemed customers.

Automatic transmissions in Ford are pretty much standard nowadays — if you want a manual, you may have to request for it or get it custom built. Automatic has made driving seamless and easier than ever, and not to forget the added power output, which manual models can’t deliver. But just because it has revolutionized the way we drive, doesn’t mean it will work as smoothly as new for years to come. You will need to do a lot of things to keep it in tip-top shape. But you will also need to avoid a few things to prevent its breakdown.

Here are a few things you should never do to Ford’s automatic transmission:

Don’t drive through deep water

It’s tempting to test your new Ford truck’s ability to cross a creek. Or perhaps, the roads are flooded, and you have no way around to get home. But if you drive through deep water, the chances of transmission damage quadruple. Water can go into the vents of your Ford’s auto transmission and may destroy the transmission beyond repair. Sure, you may get lucky, but it’s usually not worth the risk, as transmission repairs are heavy on pockets.

Avoiding going straight from reverse to drive when the vehicle is mobile

Many drivers whip the transmission into drive while they are backing up, thinking it’s fine to do it. But you might want to change this habit or avoid it in the first place. When you switch from reverse to drive or vice versa without stopping the vehicle completely, you put pressure on the transmission bands and clutch plates, which can ruin the transmission and lead to hefty repairs. It’s best to stop the vehicle first and then switch to reverse from the drive and vice versa.

Avoid leaving the transmission in the drive when idling

Whether you stopped your Ford because of traffic or any other reason, leaving the transmission in drive can lead to overheating inside it, which can impact its lifespan. So, when you are idling the vehicle for a while, make sure to shut the transmission down completely. This way, Ford’s auto transmission won’t be sending power, which prevents overheating.

Don’t forget to change the transmission fluid

Many people overlook the importance of replacing automatic transmission fluid (ATF) under normal driving conditions. However, it’s a blunder that invites plenty of transmission issues, including its complete failure. As a rule of thumb, it’s best to avoid driving with dirty transmission fluid. Always replace it as per the manufacturer’s recommendations.

Don’t coast down in neutral

Many drivers think of saving gas when coming downhill by coasting down in neutral. However, that’s not true. While it may work with manual transmissions, Ford’s auto transmission may deliver more gas to the engine to prepare for the start because of the increase in the ROM while in neutral. So, you are not saving gas but using more by coming downhill in neutral.

It’s also vital to avoid driving your Ford when you are noticing transmission fluid leaks. In such cases, the best course of action is to visit a repair shop immediately and get the leaks fixed.

If you are looking for automatic transmission for your Ford, get in touch with us and discuss your requirements. We are a team of experts who custom build Ford’s auto transmission to improve your driving experience.